5
and the tool will shut off. Release the trigger.
NOTE:
Workpiece may move slightly during the cut.
4. Two LEDs will light when the trigger is pulled.
WARNING
To reduce the risk of injury, only
cut recommended materials for the
jaws (see "Specifications"). Do not attempt to cut
other materials.
Cutting Tips
• Cut farther in from the end of the material to avoid
crooked cuts.
•
Do not attempt angled cuts. It will damage the blades.
Hold the material squarely between the blades.
•
Cut clean material to extend the blade life. Wipe dirt
and debris from material and blades before begin-
ning the cut.
•
Do not cut 477 ACSR materials with 750 MCM Cu jaws.
Do not cut 750 MCM Cu materials with 477 ACSR
jaws. It could damage the blades, jaws, and tool.
•
When using the 477 ACSR jaws, ensure the blade
retainer is installed.
•Only use the jaws on the material for which it was
designed. Other materials could damage t
he blades,
jaws, and tool.
Backup Release Valve
If the jaws need to be opened without completing the
cycle, press and hold the backup release valve. Hold
tool securely until the cylinder retracts fully.
Jammed Blades
Dirt and debris can cause the blades to become
jammed together after a cut. If the tool shuts off and
the blades are still closed:
1. Press and hold the backup release valve to ensure
the tool has reset.
2. Remove the battery pack.
3. Remove the jaws from the tool.
4. Use a soft mallet to tap the rear of the jaws to release.
5. Clean any dirt and debris from the blades before
starting another cut.
MAINTENANCE
WARNING
To reduce the risk of injury, always
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop
-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
ONE-KEY™
Refer to the ONE-KEY™ App for information regard
-
ing necessary servicing, such as internal battery life
and crimp count.
WARNING
Chemical Burn Hazard.
This device contains a
lithium button/coin cell battery. A new
or used battery can cause severe in
-
ternal burns and lead to death in as
little as 2 hours if swallowed or enters the body.
Always secure the battery cover. If it does not close
securely, stop using the device, remove the bat
-
teries, and keep it away from children. If you think
batteries may have been swallowed or entered
the body, seek immediate medical attention
.
Internal Battery
An internal battery is used to facilitate full ONE-KEY™
functionality.
To replace the battery:
1. Remove the battery pack.
2. Remove the screw(s) and open the battery door.
3. Remove the old battery, keep it away from children,
and dispose of it properly.
4. Insert the new battery (3V CR2032), with the posi
-
tive side facing up.
5. Close the battery door and tighten the screw(s)
securely.
Jaws and Blades
Inspect jaws for cracks or damage. Do not use dam
-
aged jaws. Replace the blades when they become
dull, rounded, chipped, or damaged.
Hydraulic Fluid
To extend the life of the tool, return the tool to a
MILWAUKEE service facility for hydraulic fluid re
-
placement after 20,000 cuts or 2 years of use.
WARNING
To reduce the risk of personal in-
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Cleaning
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these harmful agents
include gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia and
household detergents containing ammonia. Never
use flammable or combustible solvents around tools.
Repairs
For repairs, return the tool, battery pack and charger
to the nearest service center.
ACCESSORIES
WARNING
Use only recommended accesso-
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST
(1.800.729.3878)
Monday-Friday, 7:00 AM - 6:30 PM CST
or visit
www.milwaukeetool.com
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: [email protected]
Become a Heavy Duty Club Member at
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
