4
ONE-KEY™
To learn more about the ONE-KEY™ functionality
for this tool, go to milwaukeetool.com/One-Key. To
download the ONE-KEY™ app, visit the App Store or
Google Play from your smart device.
ONE-KEY™ Indicator
Solid Blue
Wireless mode is active and ready
to be configured via the ONE-KEY™
app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red
Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
OPERATION
WARNING
To reduce the risk of injury, always
wear proper eye protection marked
to comply with ANSI Z87.1.
Always remove battery pack before changing
or removing accessories. Only use accessories
specifically recommended for this tool. Others
may be hazardous.
Always hold tool securely and anticipate a sud-
den reaction.
Using the Rivet Tool
1. Prepare the workpiece. If
necessary, drill a pilot hole.
2.
Place the blind rivet mandrel
into the nose piece.
3.
Insert the rivet end into the
workpiece. Hold the tool
securely and pull and hold
the trigger until the rivet is
fully set and the motor stops.
Release the trigger. The tool
will reset.
NOTE:
Releasing the trigger
before the rivet is fully set will
cause the tool to return to its
starting position.
4.
After setting the blind rivet,
insert the next rivet to push
the spent mandrel to the
mandrel collector.
5.
Empty the mandrel collector
after setting 100-150 rivets,
depending on size.
*The included retention nose
pieces (49-16-2660RP) hold
inserted blind rivets in place
while operating the tool in any orientation.
*CherryMAX
®
rivet installation is not recommended
with retention nose pieces (49-16-2660RP). Use non-
retention nose pieces (49-16-2660NR; not included)
for increased performance with CherryMAX
®
rivets.
ASSEMBLY
WARNING
Recharge only with the charger
specified for the battery. For spe
-
cific charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To
remove
the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always lock the trigger or remove
the battery pack any time the tool
is not in use.
To
insert
the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
Only use accessories specifically
recommended for this tool. Others
may be hazardous.
Always use mandrel collector. Spent mandrels
can be ejected from the tool, causing injury.
Installing/Emptying Mandrel Collector
Once the rivet is set, the mandrel collects in the box.
Empty the mandrel collector often to avoid jamming
the tool.
WARNING!
Never use the tool without the
mandrel collector installed. Loose mandrels could
cause a hazard.
1.
To
install
the mandrel collector, line up the box
with the detents in the tool. Slide the box onto the
tool, and rotate to lock
in place.
2.
To
empty
the mandrel collector, rotate the box
and pull away from the tool. Empty the box and
reinstall before use.
Installing the Nose Piece
The rivet tool comes with 4 nose pieces for 3/16",
7/32", 1/4", and 9/32" blind rivet sizes.
1. Remove battery pack.
2.
Remove the nose housing from the tool (recom-
mended).
NOTE
: Due to the spring, it can be dif
-
ficult to install the nose piece into the nose housing
without first removing the nose housing.
3.
Remove the nose piece from
the nose housing. For ease of
use, the wrench does not need
to be removed from the tool for
use. Insert the nose housing
into the onboard wrench stor-
age and turn counterclockwise.
4.
Select the correct nose piece
for the rivet to be installed. To remove the nose
piece from the on-tool storage, use your thumb to
pull down on needed nose piece.
5. Insert the new nose piece into the nose housing.
Use the onboard wrench to hand-tighten securely.
6.
Screw the nose housing onto the tool and hand-
tighten securely.
Nose Piece
Ring Color
3/16" (4.8 mm)
Black
7/32" (6 mm)
Green
1/4" (6.4 mm)
Red
9/32" (7.0
mm)
Brown
