background image

 

6. Trouble Shooting 

 

Defective Symptom 

Possible Cause 

Recommended remedy 

Power does not turn on

Shortage of battery capacitance

 

Replace the batteries.

 

Contact failure at Battery contact  Replace the battery contact.

 

Inaccurate measurement is

caused.  

Shortage of battery capacitance

 

Replace the batteries.

 

Defect of adjustment

 

Readjustment

 

Defect of circuit components 

Replace the PCB. 

Defect of circuit sensor module 

Replace the sensor module. 

Display value changes over 

20digits at  zero point ,  when 

repeating  the JAW open and 

close,  

Defect of circuit sensor module 

Replace the sensor module. 

 

Lack of the segment, or 

abnormal lighting, 

Defect of circuit components 

Replace the PCB. 

LCD  backlight  or  LED  light  is 

not lit

 

Defect of circuit components 

Replace the PCB. 

 

7.  List of Spare parts 
 

No. 

Spare parts No.

 

Parts Name

 

Qty. 

Remark

 

18 

9000018895  Lamp Button 2231-20 UL 

17 

9000019044  Lamp Button Bracket 2231-20 

9000018894

 

Control Button 2231-20 UL

 

9000018890  Enclosure-Front Case 2231-20UL 

5,6 

122310200A  2231-20 PCB MAIN 

with LCD and one screw 

9000018891  Enclosure-Rear Case 2231-20 UL 

11 

9000014595  Screw For Bottom Case 

12,13 

9000018892  Battery Door 2231-20 UL 

with two screws 

16 

122310100A  2231-20 Clamp and Wire 

with wire clip 

3,4 

9000018896  Control Button Support 2231-20 

with two screws 

14 

9000017226  Battery maxell LR6(GD)E 4PT 

 
 
 

 

Summary of Contents for 2231-20 4-20







Reviews: