Miele WMR 861 WPS Operating Instructions Manual Download Page 64

Page: 64 / 116

Detergent

Dispensing fabric softener and
liquid starch at the end of the
programme

You can dispense fabric softener either
by using automatic dispensing or via
the detergent dispenser compartment.

Automatic dispensing

One of the automatic dispensing
containers (available as an optional
accessory) must be filled with fabric
softener.



Touch the

Dos



sensor.



Activate the appropriate container.

Fabric softener will be dispensed in the
last rinse.

Manual dispensing



Add the fabric softener or liquid
starch to the



compartment or

insert the appropriate capsule.

not exceed the maximum level
mark.

It will be automatically dispensed in the
final rinse. At the end of the programme
a small amount of water will remain in
the



compartment.

If starching frequently, thoroughly
clean the dispenser compartment,
especially the siphon tube, regularly.

Summary of Contents for WMR 861 WPS





















































































































Search results

Summary of Contents for WMR 861 WPS

Reviews:

Related manuals for WMR 861 WPS

Brands by name

Popular brands

Miele WMR 861 WPS, Operating Instructions Manual

Search results

Summary of Contents for WMR 861 WPS

Reviews:

Related manuals for WMR 861 WPS

Brands by name

Popular brands