Miele WMR 861 WPS Operating Instructions Manual Download Page 35

Page: 35 / 116

Spinning

Final spin speed

Programme

Max. possible

rpm

Cottons

1600

Minimum iron

1200

Delicates

900

Woollens



1200*

Denim

900

Outerwear

800

Automatic plus

1400

Dark garments

1200

Shirts

900

Down duvets

1200

Silks



600*

Sportswear

1200

Proofing

1000

Separate rinse

1600*

Starch

1400*

Down filled items

1200

Curtains

600

First wash

1200

Pillows

1200

Drain/Spin

1600

Clean machine

900

Freshen up

–

Mixed items

1200-1600

QuickPowerWash

1600

Express 20

1200

Steam care

–

Final spin speed in the
programme

When a programme is selected, the
optimum spin speed for that
programme will appear in the display.
For programmes marked with a

in the

chart, the optimum spin speed is not
the maximum spin speed.

You can reduce the final spin speed or,
depending on the programme, increase
it.

However, you cannot select a final spin
speed higher than that shown in the
chart.

Rinse and interim spin

There is a spin after the main wash and
between the rinses. A reduction in the
final spin speed will also reduce the
interim spin speed. If a spin speed of
less than 700 rpm is selected for the

Cottons

programme, an additional rinse

is introduced.

Summary of Contents for WMR 861 WPS





















































































































Search results

Summary of Contents for WMR 861 WPS

Reviews:

Related manuals for WMR 861 WPS

Brands by name

Popular brands

Miele WMR 861 WPS, Operating Instructions Manual

Search results

Summary of Contents for WMR 861 WPS

Reviews:

Related manuals for WMR 861 WPS

Brands by name

Popular brands