Miele W 939 WPS Operating Instructions Manual Download Page 7

Page: 7 / 68

Control panel

I-On/0-Off button

for switching the machine on or off
or interrupting a programme

Door button

opens the machine door

CHECK LIGHTS

PROGRAMME touch pads

ADDITIONAL OPTION touch pads

Indicator light on = option selected
Indicator light off = option not se-
lected

TEMPERATURE display

with

touch pads for setting the

wash temperature

SPIN SPEED display

with

touch pads for setting the

final spin speed

SEQUENCE display

with touch pad for changing the
programme sequence

Indicator lights for LOAD display

START touch pad

starts the wash programme

Buzzer touch pad

Delay start touch pad

with

touch pads for setting the

time

Display

The display has several functions:

– it displays the programme duration

– it displays the “Delay start” time re-

maining until a programme starts

– it displays programming functions

when they are called up

Guide to the machine

Summary of Contents for W 939 WPS





































































Search results

Summary of Contents for W 939 WPS

Reviews:

Related manuals for W 939 WPS

Brands by name

Popular brands

Miele W 939 WPS, Operating Instructions Manual

Search results

Summary of Contents for W 939 WPS

Reviews:

Related manuals for W 939 WPS

Brands by name

Popular brands