Miele W 939 WPS Operating Instructions Manual Download Page 31

Page: 31 / 68

Electronic Locking

The locking function prevents your
machine being used without your
knowledge.

When the locking function is switched
on:

– the machine cannot be opened,

– a programme cannot be selected,

– the machine cannot be started.

Switching on the locking function

Shut the drum door.

Switch on the machine.

Press the

Pre-wash

touch pad and

hold pressed in while carrying out
steps

and

Press the

Mixed Wash

touch pad

once.

Press the

Minimum iron

touch pad

once.

– The

locked

check light flashes, (up-

per left on the control panel).

Release the

Pre-wash

touch pad.

Switch off the machine.

To switch off the locking function

Repeat steps

. The check light

locked

goes out.

Additional options

Summary of Contents for W 939 WPS





































































Search results

Summary of Contents for W 939 WPS

Reviews:

Related manuals for W 939 WPS

Brands by name

Popular brands

Miele W 939 WPS, Operating Instructions Manual

Search results

Summary of Contents for W 939 WPS

Reviews:

Related manuals for W 939 WPS

Brands by name

Popular brands