Miele W 2653 WPS Operating Instructions Manual Download Page 41 | Manualshive

Page: 41 / 72

background image

The drum door cannot be opened by pressing the Door button

Possible cause

Remedy

The machine is not
connected to the
electricity supply and / or
is not switched on.

Insert the plug in the socket and switch on and / or
switch the machine on with the

I-On/0-Off

button.

The electronic programme
lock has been activated.

Deactivate programme locking as described in
"Electronic programme locking".

The electronic system lock
has been activated.

Deactivate the system lock as described in the
"Settings

J

menu".

Power cut

Open the drum door as described in the next
section.

The door was not correctly
engaged.

Press hard against the lock side of the drum door
and then press the

Door

button.

There is still water in the
drum and the machine is
unable to drain.

Clean the fluff filter and drain pump as described
in the next section.

For safety reasons the drum door cannot be opened when the suds temperature
is higher than 55°C.

Problem solving guide

41

«
...
39
40
41
42
43
...
»

Summary of Contents for W 2653 WPS









































































Reviews:

No comments

Related manuals for W 2653 WPS

Brand: Haier Pages: 10

Brand: Haier Pages: 10

Brand: Haier Pages: 18

Brand: Haier Pages: 18

Brand: Haier Pages: 18

Brand: Haier Pages: 40

Brand: Haier Pages: 15

Brand: Haier Pages: 8

Brand: Haier Pages: 18

Brand: Haier Pages: 20

Brand: Haier Pages: 10

HW-C1470TVE ME-U

Brand: Haier Pages: 19

Brand: Haier Pages: 20

Brand: Haier Pages: 20

Brand: Haier Pages: 19

Brand: Haier Pages: 16

Brand: Haier Pages: 18

Brand: Haier Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands