Miele W 2653 WPS Operating Instructions Manual Download Page 37

Page: 37 / 72

Fault messages in the display

Problem

Possible cause

Remedy

DRAIN FAULT

–

The water outlet is
blocked or restricted.

–

The drain hose has
been fixed too high.

–

Clean the fluff filter and
the drain pump.

–

The maximum drain
height is 1 m.

INLET FAULT

–

The water inlet is
blocked or restricted.

Check whether

–

the stopcock is opened
wide enough.

–

the inlet hose is kinked.

WPS ACTIVATED

The water protection
system has reacted.

Call the Service
Department.

DRUM LIGHTING
FAULT

The drum light is not
locked in position.

Check that the drum light is
sitting correctly.

TECHNICAL
FAULT
call Service Dept

There is a fault.

Start the programme again.
If the fault message
appears again, contact the
Service Department.

To delete the fault message: Switch the washing machine off with the

I-ON/0-OFF

button.

Problem solving guide

Summary of Contents for W 2653 WPS









































































Search results

Summary of Contents for W 2653 WPS

Reviews:

Related manuals for W 2653 WPS

Brands by name

Popular brands

Miele W 2653 WPS, Operating Instructions Manual

Search results

Summary of Contents for W 2653 WPS

Reviews:

Related manuals for W 2653 WPS

Brands by name

Popular brands