Miele W 2653 WPS Operating Instructions Manual Download Page 18 | Manualshive

Page: 18 / 72

background image

F

Start the programme

^

Press the flashing

Start/Stop

T

button.

The estimated programme duration will
appear in the display. This will count
down in one minute steps. During the
first 10 minutes the washing machine
measures how much water is being
absorbed by the laundry. The
programme duration may be longer or
shorter depending on this absorbency
rate.

The programme sequence is also
shown in the display. The washing
machine shows you when each section
of the programme is reached.

The drum lighting switches off once the
programme has started.

G

Remove the laundry

Anti-crease

and

Finish

will flash

alternately in the display to indicate that
the programme has finished.

^

Prss the

Door

button to open the

drum door.

^

Remove the laundry.

Make sure that the drum is empty.
Items left in the drum could
discolour other items in the next
wash or become discoloured
themselves.

^

Check the folds in the door seal for
any small articles, e.g. buttons which
might be lodged there.

^

Switch the washing machine off with
the

I-ON/0-OFF

button.

^

Close the drum door. Otherwise there
is the danger of objects being placed
inadvertently in the drum. If these
remained unnoticed and were
washed in the next load, they could
damage the laundry.

How to wash correctly

18

«
...
16
17
18
19
20
...
»

Summary of Contents for W 2653 WPS









































































Reviews:

No comments

Related manuals for W 2653 WPS

Sicily Glory G01

Brand: Midea Pages: 65

Aquarius WDF 756 A

Brand: Hotpoint Pages: 16

Brand: Kärcher Pages: 12

Brand: Kärcher Pages: 12

Brand: Spitwater Pages: 23

MVWC300VW - Centennial Washer

Brand: Maytag Pages: 20

Brand: BE Pages: 19

Brand: Hotpoint Ariston Pages: 24

Brand: GE Pages: 20

Brand: GE Pages: 20

WF8694AH(A/C/D/F/G/H/R/S/T/V/W/Z)(U)

Brand: Samsung Pages: 72

Brand: Samsung Pages: 208

Brand: Samsung Pages: 132

Brand: Samsung Pages: 132

Brand: Zanussi Pages: 40

Brand: HAEGER Pages: 104

Brand: Primus Pages: 112

Full Size Laundry Center Gas

Brand: Frigidaire Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands