Miele W 2652 WPS Operating Instructions Manual Download Page 67

Page: 67 / 72

Keypad tones

An audible tone sounds each time a
button is pressed.

The washing machine is delivered with
the keypad tone switched off.

A tick will appear beside the option to
show that it has been set.

Back

Off

Select the option you want and
confirm your selection.

Display contrast

There are ten different display
contrast settings.

The machine is delivered with the
display contrast on Setting 5.

The display contrast will change as
soon as a different setting is chosen.

dimmer

brighter

Set contrast

Set the display contrast you require.

Display brightness

There are ten different display
brightness settings.

The machine is delivered with the
display brightness on Setting 5.

The display brightness will change as
soon as a different setting is chosen.

dimmer

brighter

Set brightness

Set the display brightness you
require.

Settings menu

Summary of Contents for W 2652 WPS









































































Search results

Summary of Contents for W 2652 WPS

Reviews:

Related manuals for W 2652 WPS

Brands by name

Popular brands

Miele W 2652 WPS, Operating Instructions Manual

Search results

Summary of Contents for W 2652 WPS

Reviews:

Related manuals for W 2652 WPS

Brands by name

Popular brands