Miele W 2652 WPS Operating Instructions Manual Download Page 9

Page: 9 / 72

Control panel

PROGRAMME buttons

with

indicator lights
For selecting a washing programme.

Extra options buttons

with indicator

lights
Various Extra options can be added
to the washing programmes.

PC / Optical interface

This is used by service technicians
to run diagnostic checks on your
machine and can also be used to
update programming data in the
future.

button

For selecting delay start.

Display with – , OK, + and Load/
Detergent buttons

See the following page for more
details.

Start/Stop button

For starting the programme selected
and cancelling a programme once it
has started.

I-On/0-Off button

For switching the washing machine
on or off.

Door button

Opens the machine door.

Description of the machine

Summary of Contents for W 2652 WPS









































































Search results

Summary of Contents for W 2652 WPS

Reviews:

Related manuals for W 2652 WPS

Brands by name

Popular brands

Miele W 2652 WPS, Operating Instructions Manual

Search results

Summary of Contents for W 2652 WPS

Reviews:

Related manuals for W 2652 WPS

Brands by name

Popular brands