Miele W 2652 WPS Operating Instructions Manual Download Page 10

Page: 10 / 72

Display

– / + button

For changing the values shown in the
display:

–

decreases the value or moves the
highlighting up a line.

increases the value or moves the
highlighting down a line.

OK button

For confirming the value selected and
choosing the next value.

Load, Detergent button

For calling up the load size and the
detergent amount and for calibrating
the load size sensor to zero.

When a programme is selected, the
display is used to select:

– the temperature

– the final spin speed

– the soak time

– delay start

– a special programme

The display shows:

– the duration of the wash programme

– the current time of day.

The "Settings

" menu is also operated

via the display.

Description of the machine

Summary of Contents for W 2652 WPS









































































Search results

Summary of Contents for W 2652 WPS

Reviews:

Related manuals for W 2652 WPS

Brands by name

Popular brands

Miele W 2652 WPS, Operating Instructions Manual

Search results

Summary of Contents for W 2652 WPS

Reviews:

Related manuals for W 2652 WPS

Brands by name

Popular brands