Miele W 2652 WPS Operating Instructions Manual Download Page 62

Page: 62 / 72

To open the Settings menu

Switch on the washing machine. The
main menu will appear.

15:03

Select programme

After 5 seconds an additional line will
appear in the display.

15:03

Select programme

SETTINGS

...

Press the OK button.

This will take you into the

Settings

menu.

Back

LANGUAGE

...

TIME OF DAY...

Use the

–

and

buttons to select the

setting you want and confirm your
selection by pressing the OK button.

Important:

If you do not make a selection in the
Settings menu and in its sub-menus
within approx. 20 seconds, the menu
display will revert to the main menu.

Language

The display shows several different
languages.

You can select one of the languages
displayed via the Language sub-menu.

The flag after the word

Language

acts

as a guide to prevent a language which
will not be understood from being set.

A tick will appear beside the language
to show that it has been set.

Back

deutsch

english

Select the language you want and
confirm your selection.

Settings menu

Summary of Contents for W 2652 WPS









































































Search results

Summary of Contents for W 2652 WPS

Reviews:

Related manuals for W 2652 WPS

Brands by name

Popular brands

Miele W 2652 WPS, Operating Instructions Manual

Search results

Summary of Contents for W 2652 WPS

Reviews:

Related manuals for W 2652 WPS

Brands by name

Popular brands