Miele W 2652 WPS Operating Instructions Manual Download Page 12

Page: 12 / 72

Running your first programme

Your washing machine is now ready for
the first programme to be run.

15:00

Select programme

Press the programme button for

Cottons Universal

Press the

Start/Stop

button.

At the end of the programme switch
the machine off.

The load sensor must then be
calibrated to zero as you would with
bathroom scales.

Calibrating the load sensor to zero

Switch the washing machine on.

Open the drum door.

Press the programme button for

Cottons Universal

Press and hold the

Load/Detergent

button until the following appears in
the display:

Zero setting
OK

Switch the washing machine off.

The drum settles a little during the
first few washes and will take 3 or 4
wash cycles to reach its true position.
For this reason, please re-calibrate
the sensor to zero after each of the
first few wash cycles.

The machine is now ready for use.

Before using for the first time

Summary of Contents for W 2652 WPS









































































Search results

Summary of Contents for W 2652 WPS

Reviews:

Related manuals for W 2652 WPS

Brands by name

Popular brands

Miele W 2652 WPS, Operating Instructions Manual

Search results

Summary of Contents for W 2652 WPS

Reviews:

Related manuals for W 2652 WPS

Brands by name

Popular brands