Miele PWM 912 Operating And Installation Instructions Download Page 7

IMPORTANT SAFETY INSTRUCTIONS

7

Appropriate use

 

The washing machine is only suitable for washing fabrics with a

care label stating that they are suitable for machine washing. Any
other applications may be hazardous. The manufacturer cannot be
held responsible for damage resulting from incorrect or improper use
or operation of the machine.

 

This washing machine must be used as described in the Operating

Instructions and must be checked on a regular basis to make sure it
is functioning correctly. Maintenance must be carried out when nec-
essary.

 

The washing machine is not suitable for outdoor use.

 

Do not install the washing machine in a room where there is a risk

of frost. Frozen hoses are at risk of tearing or bursting. The reliability
of the electronic may be impaired at temperatures below freezing
point.

 

This washing machine is intended only for use in an industrial envi-

ronment.

 

If the washing machine is operated in a industrial environment, it

must only be operated by instructed / trained personnel or special-
ists. If the machine is operated in a publically accessible area, the op-
erator must ensure its safe use.

 

The washing machine must not be installed or operated in mobile

installations (e.g., on ships).

 

Persons who lack physical, sensory or mental abilities, or experi-

ence with the appliance should not use it without supervision or in-
struction by a responsible person.

 

Children must not be allowed near the washing machine unless

they are constantly supervised.

 

Children must not be allowed to clean or maintain the washing ma-

chine.

 

Please supervise children in the vicinity of the washing machine

and do not let them play with it.

 

Disinfection programs must not be interrupted, as this can have a

limiting effect on the disinfection result. It is the operator’s responsi-
bility to ensure that the standard of disinfection in thermal as well as
chemo-thermal procedures is maintained by carrying out suitable val-
idation tests.

Summary of Contents for PWM 912





































































Reviews: