manualshive.com logo in svg

Miele PWM 912, Operating And Installation Instructions

Share
Download
Miele PWM 912 Operating And Installation Instructions Download Page 56

Supervisor level

56

Program selection

Controls

You can select whether the washing machine is operated as a laun-
dromat machine. Shortcuts are the easiest way to operate the ma-
chine. Operating staff are unable to change pre-set programs.

Tip: 

Start by configuring all necessary settings and changes to the

washing machine before adjusting any of the options below.

If “Laundromat, basic” or “Laundromat, Logo” are selected, the Su-
pervisor level can no longer be opened from the display after the 

Su-

pervisor level

 is closed. Please follow the instructions below if you

wish to change any other settings.

Opening the Su-
pervisor level (laun-
dromat version)

Switch on the washing machine and open the door.

Touch the 

Start/Stop

 sensor control and hold it down while carrying

out steps 

–

.

Close the washing machine door.

The Start/Stop sensor control will now be flashing quickly; wait un-
til it lights up constantly.

Release the 

Start/Stop

 sensor control when the 

Start/Stop

 sensor

control lights up constantly.

Standard (factory default).

All functions and programs can be displayed.

Laundromat, basic

Up to 12 programs are available. Go to 

Favorite programs

 to select

which programs are to be listed.

Laundromat Logo

Up to 12 programs are available. Go to 

Favorite programs

 to select

which programs are to be listed.

External program selection

Programs are selected using a communication module, e.g., an exter-
nal terminal.

Summary of Contents for PWM 912





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands