manualshive.com logo in svg

Miele PWM 912, Operating And Installation Instructions

Share
Download
Miele PWM 912 Operating And Installation Instructions Download Page 41

Installation

41

Installing the washing machine

The washing machine must be installed by Miele Customer Service
or by an authorized dealer. Please observe the instructions in the
installation plan.

This washing machine is only intended for items of laundry that
have not been proofed with dangerous or inflammable substances.

To avoid the risk of frost damage, the washing machine must not be
located in rooms which may be subject to very low temperatures.

Transport the machine inside the room on a pallet jack.

Do not remove or alter the feet of the machine.
They could be damaged.

Remove packaging carefully with a suitable tool.

Lift the machine off the pallet using a pallet jack.

Securing the machine

The feet of the washing machine must be secured to the concrete
base using the fixtures and fastenings supplied.

Fittings supplied are for installation on a concrete floor. For other
types of flooring please purchase suitable fitting materials sepa-
rately.

General operating conditions

This washing machine is intended only for use in a industrial environ-
ment and must only be operated indoors.

Ambient temperature in installation room: 32 °F (0°C) to 140 °F (40°C).

Relative humidity: non-condensing

Depending on the nature of the installation site, sound emissions and
vibration may occur.

Tip: 

Have the installation site inspected and seek the advice of a pro-

fessional in instances where increased noise may cause a nuisance.

Summary of Contents for PWM 912





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands