Miele PG 8593 Operating Instructions Manual Download Page 149

Page: 149 / 188

Installation

149

Installation and levelling

Please refer to the installation diagram provided.



In order to reduce the risk of water damage, the area around the

machine should be limited to furniture and fittings that are designed
for use in commercial environments.

The machine must be stable and horizontal.

Any unevenness in the floor level and height of the machine can be
compensated for by adjusting the four feet. The feet can be screwed
out to a maximum of 6 cm.

The machine is suitable for the following types of installation:

– Freestanding.

– Slot-in:

The machine can be installed beside other appliances or furniture
or in a suitable niche. The niche must be at least 600 mm wide and
600 mm deep.

– Built-under:

The machine can be built under a continuous worktop. The space
provided must be at least 600 mm wide, 600 mm deep and
820 mm high.

Summary of Contents for PG 8593





























































































































































































Search results

Summary of Contents for PG 8593

Reviews:

Related manuals for PG 8593

Brands by name

Popular brands

Miele PG 8593, Operating Instructions Manual

Search results

Summary of Contents for PG 8593

Reviews:

Related manuals for PG 8593

Brands by name

Popular brands