Miele H 5081 BP Page 63 Operating And Installation Manual Download

Page: 63 / 84

To remove the oven door

The oven door is connected to the oven
by hinges.

Before removing the door, the locking
clamps on both hinges have to be
released.

Open the door fully.

To release the locking clamps on the
hinges turn them upwards as far as
they will go until they are at an angle.
See illustration.

Then lift the door upwards as far as it
will go.

Do not attempt to take the door off
the hinge guides when it is in a
horizontal position. The hinge guides
will close, and damage the
appliance. Danger of injury.

Hold the door securely at both sides
and lift upwards off the hinge guides.

Do not lift the door off by the handle.
The handle could break and
damage the door.

Make sure that you lift the door off
equally on both sides.

Cleaning and care

Summary of Contents for H 5081 BP





















































































Search results

Summary of Contents for H 5081 BP

Reviews:

Related manuals for H 5081 BP

Brands by name

Popular brands

Miele H 5081 BP, Operating And Installation Manual

Search results

Summary of Contents for H 5081 BP

Reviews:

Related manuals for H 5081 BP

Brands by name

Popular brands