Miele G 7764 SUPER-COMBI Operating Instructions Manual Download Page 33 | Manualshive

Page: 33 / 44

background image

Cleaning and Care

Cleaning the filters in the water
inlet

Filters are incorporated in the screw
connection of the water inlet valve for
protection. The filters must be cleaned
when dirty otherwise insufficient water
flows into the wash cabinet.

Turn off stopcocks.

Unscrew the water inlet hoses.

Clean large area filter (1) and fine filter
(2), or replace if necesary.

After reconnection turn on the stop-
cock gently to test for leaks.

There is a further filter in front of the
water inlet valve which must only be
cleaned or replaced by a suitably com-
petent person.

2

1

Cleaning and Care

29

«
...
31
32
33
34
35
...
»

Summary of Contents for G 7764 SUPER-COMBI













































Reviews:

No comments

Related manuals for G 7764 SUPER-COMBI

Brand: Fisher & Paykel Pages: 56

SINGLE DISHDRAWER DD24SCTX9

Brand: Fisher & Paykel Pages: 3

Brand: Hanseatic Pages: 78

Brand: Hamach Pages: 55

Brand: Mach Pages: 41

Brand: Hotpoint Ariston Pages: 64

Brand: BOMANN Pages: 15

Brand: Saturn Pages: 12

Brand: Philco Pages: 108

Brand: Smeg Pages: 37

LAVAMAT L 72805

Brand: AEG Electrolux Pages: 44

Brand: Haier Pages: 12

Brand: Haier Pages: 18

Brand: Haier Pages: 18

Brand: Haier Pages: 18

Brand: Haier Pages: 16

Brand: Haier Pages: 18

Brand: Haier Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands