manualshive.com logo in svg

Miele G 6892, Operating Instructions Manual, Page: 86 / 112

Share
Download
Miele G 6892 Operating Instructions Manual Download Page 86

Problem solving guide

86

Problem

Possible cause and remedy

White residue is visible
on cutlery and crockery,
clouding occurs on
glassware; film can be
wiped off.

Not enough rinse aid was used.

Increase the dosage (see "Settings menu - Rinse
aid").

There is no salt in the salt reservoir.

Fill the salt reservoir (see "Before using for the first
time - Dishwasher salt").

An unsuitable combination detergent has been used.

Change your detergent. Use a standard liquid,
tablet or powder detergent, and fill the salt and
rinse aid reservoirs in the dishwasher.

The water softener is programmed to too low a water
hardness level.

Programme the water softener to a higher water
hardness level (see "Settings menu - Water
hardness").

There are rust stains on
cutlery.

The affected items are not corrosion resistant.

There is no remedy.
Purchase cutlery which is dishwasher-proof.

A programme was not run after dishwasher salt was
added. Traces of salt have got into the wash cycle.

Always run the 

QuickPowerWash

 programme with

the 

Short

 programme option selected and without

any crockery in the dishwasher after adding
dishwasher salt.

Summary of Contents for G 6892

















































































































Reviews:

No comments