manualshive.com logo in svg

Miele G 6892, Operating Instructions Manual, Page: 107 / 112

Share
Download
Miele G 6892 Operating Instructions Manual Download Page 107

Settings menu

107

Soak

You can use this function to loosen
dried-on food residues in the
programme selected.
Once activated, this function will be
carried out with all programmes until
you deactivate it.
If you are using powder dishwasher
detergent, add approx. 5 g to
compartment I.

Select the setting you want and
confirm with 

OK

.

Pre-wash

You can use this function to remove
easily loosened food residues in the
programme selected.
Once activated, this function will be
carried out with all programmes until
you deactivate it.

Select the setting you want and
confirm with 

OK

.

Brightness

There are seven different display
brightness settings.

Select the brightness you want and
confirm this with 

OK

.

Volume

A sequence of audible tones will sound
at the end of the programme or if there
is a fault as long as the buzzer has been
activated.

Buzzer in the event of a fault

The buzzer in the event of a fault will
sound four times at intervals with a
short pause between each set of tones.

The buzzer which sounds when there
is fault cannot be deactivated.

Buzzer at the end of a programme

The buzzer at the end of a programme
will sound four times at intervals with a
short pause between each set of tones.

The volume of the buzzer which sounds
at the end of the programme can be set
to one of seven stages. If no volume is
selected, the buzzer is switched off.

Select the 

Buzzer tones

 option.

Use the 



 arrow buttons to set the

volume required and confirm your
selection with the 

OK

 button.

Keypad tone

An audible tone sounds each time a
button is pressed.

The volume of the keypad tone can be
set to one of seven stages. If no volume
is selected, the keypad tone is switched
off.

Use the 



 arrow buttons to set the

volume required and confirm your
selection with the 

OK

 button.

Summary of Contents for G 6892

















































































































Reviews:

No comments