Miele G 6892 Page 103 Operating Instructions Manual Download

Page: 103 / 112

Settings menu

103

Networking

Your dishwasher is equipped with an
integrated Wi-Fi module.

In order to connect your dishwasher to
your Wi-Fi network, you must first
activate the network function.

This will add the

Miele@home

option to

the "Settings" menu.

Networking is deactivated ex-works.

Make sure that your Wi-Fi network
signal strength is strong enough at
the installation site of your
dishwasher.



Select the setting you want and
confirm with

Miele@home

This option is only displayed if you
have activated the network settings
(see "Settings, Networking").

There are a number of ways of
connecting your dishwasher to your Wi-
Fi network:

Miele@mobile App (only functional in
selected countries)

The Miele@mobile App can be used to
connect to your network.



Download the Miele@mobile App
from one of the App stores.



Follow the instructions in the App.

Summary of Contents for G 6892

















































































































Search results

Summary of Contents for G 6892

Reviews:

Related manuals for G 6892

Brands by name

Popular brands

Miele G 6892, Operating Instructions Manual

Search results

Summary of Contents for G 6892

Reviews:

Related manuals for G 6892

Brands by name

Popular brands