Miele G 6892 Page 23 Operating Instructions Manual Download

Page: 23 / 112

Before using for the first time

Basic settings



Open the door.



Switch the dishwasher on with the



button.

The welcome screen will appear when
the dishwasher is switched on for the
first time.

Language

The display will change automatically to
the screen for setting the language.



Use the



arrow buttons to select

the language you want and also the
country, if appropriate, and confirm
your selection with

To learn about the display, read the
section with the same name.

A tick



will appear next to the

language that has been set.

Time of day

The display will then change to the
screen for setting the time.

The current time of day must be set
before you can use the "FlexiTimer"
programme option.



Use the



arrow buttons to set the

hour and confirm with



Then set the minutes and confirm
with

Keeping the



arrow buttons

pressed in will increase or decrease
the time automatically.

Summary of Contents for G 6892

















































































































Search results

Summary of Contents for G 6892

Reviews:

Related manuals for G 6892

Brands by name

Popular brands

Miele G 6892, Operating Instructions Manual

Search results

Summary of Contents for G 6892

Reviews:

Related manuals for G 6892

Brands by name

Popular brands