Miele G 681 Operating Instructions Manual Download Page 47

Page: 47 / 64

Problem

Possible cause

Remedy

The indicator light
“Intake/Drain” is flash-
ing and the program
does not continue

Before fixing the problem
you must:

–

Turn the program se-
lector to the “Stop” po-
sition.

–

Turn off the dishwasher
using the “On/Off” but-
ton.

Water intake is restricted.

–

Open the water valve
completely.

–

Check the water inlet
filter and clean if nec-
essary, see “Cleaning
the water inlet filter”.

Water outlet is restricted,
water remains in the wash
cabinet at the end of a
program.

–

Clean the filter combi-
nation, see “Cleaning
and Care”.

–

Clean the drain pump,
see “Cleaning the drain
pump and non-return
valve”.

–

Clean the non-return
valve, see “Cleaning
the drain pump and
non-return valve”.

–

Remove any kink in the
drain hose.

Knocking noise
in the wash cabinet

The spray arm is knock-
ing against something in
the basket.

Interrupt the program,
rearrange items that are
blocking spray arms.

Rattling noise

Items are not secure in
the wash cabinet.

Interrupt the program, re-
arrange dishes.

A whistling noise is
heard during the pro-
gram

The seal of the circulation
pump sometimes makes
a whistling noise. This
may be due to the deter-
gent.

This is not a problem. Try
another detergent. Con-
sult the Miele Technical
Service Department if the
noise is persistent.

Problem solving guide

Summary of Contents for G 681

































































Search results

Summary of Contents for G 681

Reviews:

Related manuals for G 681

Brands by name

Popular brands

Miele G 681, Operating Instructions Manual

Search results

Summary of Contents for G 681

Reviews:

Related manuals for G 681

Brands by name

Popular brands