Miele G 681 Operating Instructions Manual Download Page 58

Page: 58 / 64

Program chart

Program

When to use

Detergent

chlorine

free

containing

chlorine

Compart-

ment

(Wash

cycle)

Compart-

ment

(Pre-wash)

Compart-

ment

(Wash

cycle)

Normal

55 °C/130 °F

for

normal

everyday loads

100 %

20 %

80 %

Sani Wash
55 °C/130 °F

as Normal 55 °C/130 °F,
but with longer wash time for

heavily soiled

loads, also suitable for chlorine free deter-
gents

100 %

20 %

80 %

Normal
65 °C/150 °F

as Normal 55 °C/130 °F,
but at a higher temperature for

stubborn

dried on food

100 %

20 %

80 %

Light Wash
55 °C/130 °F

for

normal

everyday loads,

particularly suitable for chlorine free deter-
gents

100 %

Economy
55 °C/130 °F

for

normal

everyday loads,

particularly energy saving program

100 %

Special Program

China & Crystal
45 °C/115 °F

“Gentle program”, for

lightly soiled

and

heat sensitive

tableware

50 %

Rinse & Hold

for rinsing dishes when a complete cycle is
not needed

Energy Saver

for

lightly to normally soiled

dishware only

select Energy Saver if the dishwasher is
connected to a hot water supply
(minimum temperature 45 °C/115 °F).
– see “Choosing a program”

100 %

20 %

80 %

The dispensing method will depend on the type of detergent being used.
1) Use this ratio for:

–

detergent which is chlorine and phosphate free

–

detergent which is chlorine free but contains phosphates

In this instance the whole amount is placed in compartment II.

2) Use this ratio for:

–

powder detergent which contains chlorine and phosphates

Divide the total amount, as shown, between compartment I and compartment II.

When washing a full load in the Light Wash Program, the Normal Program, the Intensive Program or
the Economy Program 1

tablespoons (25 ml) of detergent are needed.

Program chart

Summary of Contents for G 681

































































Search results

Summary of Contents for G 681

Reviews:

Related manuals for G 681

Brands by name

Popular brands

Miele G 681, Operating Instructions Manual

Search results

Summary of Contents for G 681

Reviews:

Related manuals for G 681

Brands by name

Popular brands