Miele G 6660 Operating Instructions Manual Download Page 91

Page: 91 / 96

Water connection

The Miele Waterproof system

As long as your dishwasher has been
installed correctly, the Miele waterproof
anti-leak system will protect you from
water damage.

Connection to the water supply



Water in the dishwasher must

not be used as drinking water.

– The dishwasher may be connected to

a cold or hot water supply, max.
60°C.
We would only recommend
connection to a hot water supply if it
is economical, e.g. a solar powered
supply. When connected to a hot
water supply, all programmes will be
carried out with hot water.

– The inlet hose is approx. 1.5 m long.

– A tap with a 3/4" male thread must

be provided on site.

– IMPORTANT: Australia and New

Zealand
This appliance must be installed
according to AS/NZS 3500.1. Back
flow prevention is already integrated
in the appliance.

– The water pressure (flow pressure at

the take-off point) must be between
50 and 1000 kPa (0.5 and 10 bar). If
the water pressure is too high, a
pressure reducer valve must be fitted.

After connecting the dishwasher to
the water supply, check that all
plumbing connections are watertight.



To avoid any damage to the

appliance, the dishwasher must only
be operated when it is connected to
a fully vented plumbing system.



The inlet hose must not be

shortened or damaged in any way as
it contains electrical components
(see illustration).

Summary of Contents for G 6660

































































































Search results

Summary of Contents for G 6660

Reviews:

Related manuals for G 6660

Brands by name

Popular brands

Miele G 6660, Operating Instructions Manual

Search results

Summary of Contents for G 6660

Reviews:

Related manuals for G 6660

Brands by name

Popular brands