Miele G 6660 Operating Instructions Manual Download Page 78

Page: 78 / 96

Problem solving guide

Water inlet fault

Problem

Possible cause and remedy

The In-operation
indicator is flashing
quickly.
The buzzer is sounding.
The

Inlet/Drain

indicator is flashing on
and off.

The tap is turned off.



Turn on the tap fully.

The In-operation
indicator is flashing
quickly.
The buzzer is sounding.
The

Inlet/Drain

indicator is flashing and
fault code





has

appeared in the display.

Before rectifying the problem, you must:



Switch the dishwasher off with the



button.

Water intake is restricted.



Turn on the tap fully and start the programme
again.



Clean the water inlet filter (see "Maintenance").



The water pressure at the intake is lower than 50
kPa (0.5 bar).
Seek professional advice.

Summary of Contents for G 6660

































































































Search results

Summary of Contents for G 6660

Reviews:

Related manuals for G 6660

Brands by name

Popular brands

Miele G 6660, Operating Instructions Manual

Search results

Summary of Contents for G 6660

Reviews:

Related manuals for G 6660

Brands by name

Popular brands