Miele G 6660 Operating Instructions Manual Download Page 65

Page: 65 / 96

Programme options

Factory default settings

If you have altered any settings from the
factory default, you can reset them
back to the factory default settings as
follows:



Open the door.



Switch the dishwasher off with the



button, if it is switched on.



Press the programme selector button



in and,

whilst holding it in

, switch

the dishwasher on using the



button.
Keep the programme selector button



pressed in for at least 4 seconds

until the lower right-hand programme
indicator comes on.

If this does not happen, start the
procedure from the beginning again.



Press the



button 19 times.

The



indicator light will do 1 long

flash and 9 short flashes at intervals.

The flashing sequence in the display
indicates whether a setting has been
changed from its factory default.

–

 

: All settings are set to factory

default settings.

–

 

: At least one setting has been

changed.



To reset the dishwasher to the factory
default settings, press the
programme selector button



The setting is now stored in memory.



Switch the dishwasher off with the



button.

Summary of Contents for G 6660

































































































Search results

Summary of Contents for G 6660

Reviews:

Related manuals for G 6660

Brands by name

Popular brands

Miele G 6660, Operating Instructions Manual

Search results

Summary of Contents for G 6660

Reviews:

Related manuals for G 6660

Brands by name

Popular brands