Miele G 6660 Operating Instructions Manual Download Page 29

Page: 29 / 96

Before using for the first time

Setting the rinse aid dosage

You can adjust the rinse aid dosage for
best results.

The rinse aid dosage is set in stages
from 0 to 6. It is set to 3 at the factory.
This is the recommended setting.

If the "Adjust Automatic" programme
function (depending on model) has
been activated, the amount of rinse aid
dispensed in the

Automatic

programme

can be higher than that set.

If spots appear on crockery and
glassware:



Increase the rinse aid dosage.

If clouding or smearing appears on
crockery and glassware:



Decrease the rinse aid dosage.



Switch the dishwasher off with the



button, if it is switched on.



Press the programme selector
button



in and,

whilst holding it in

switch the dishwasher on using the



button.

Keep the programme selector
button



pressed in for at least four

seconds until the lower right-hand
programme indicator light comes on.

If this does not happen, start the
procedure from the beginning again.



Press the



button three times.

The



indicator will flash rapidly 3

times at intervals.

The dosage set will appear in the
display after



The flashing sequence

 

will appear in

the display.
This indicates the factory default setting
3.



Use the programme selector
button



to select the setting

required.
Each press of the button moves you
up a level.

The setting is now stored in memory.



Switch the dishwasher off with the



button.

Summary of Contents for G 6660

































































































Search results

Summary of Contents for G 6660

Reviews:

Related manuals for G 6660

Brands by name

Popular brands

Miele G 6660, Operating Instructions Manual

Search results

Summary of Contents for G 6660

Reviews:

Related manuals for G 6660

Brands by name

Popular brands