Miele G 6660 Operating Instructions Manual Download Page 77

Page: 77 / 96

Problem solving guide

Problem

Possible cause and remedy

The In-operation
indicator is flashing
quickly.
The buzzer is sounding.
All the programme
indicator lights flash
when the door is open.
Fault code



appears

in the display.

There may be a technical fault.



Switch the dishwasher off with the



button.



Switch the dishwasher back on after a few
seconds.



Select the programme you want.



Close the door.

If the indicator lights flash again, there is a technical
fault.



Call Miele.

Fault



The buzzer is sounding
continuously.
The drain pump may
also be running, even
with the door open.

The Waterproof system has reacted.



Turn off the tap.



Call Miele.

Fault



A fault has occurred in the circulation pump.



Switch the dishwasher off for at least 30 seconds
with the



button.



Switch the dishwasher back on.



Select the programme you want.



Close the door.

If the fault message appears again, there is a
technical fault.



Call Miele.

Summary of Contents for G 6660

































































































Search results

Summary of Contents for G 6660

Reviews:

Related manuals for G 6660

Brands by name

Popular brands

Miele G 6660, Operating Instructions Manual

Search results

Summary of Contents for G 6660

Reviews:

Related manuals for G 6660

Brands by name

Popular brands