Miele G 665 Operating Instructions Manual Download Page 60

Page: 60 / 72

6. Adjusting the door springs

The door springs are correctly adjusted
when a half opened door (approx. 45°
opening angle) remains in that position
when released.

If the door drops down, then the door
springs need to be tightened.

If, however, it rises up, then the springs
need to be released.

The adjusting screw is located in the
upper front strip at the left hand side of
the dishwasher.

Open the dishwasher door.

Adjust the door spring until it is cor-
rectly balanced:
– turn clockwise = tighten
– turn anti-clockwise = loosen.

Push the dishwasher back into its
recess.

7. Level and secure the

dishwasher

To ensure the stability of the dish-
washer it must be screwed to the con-
tinuous worktop after it has been posi-
tioned.

Half open the dishwasher door.

Screw one of the 4 x 15 screws (sup-
plied) from below into the holes in
the right and left hand side of the
upper strip.

Do not lift the dishwasher to do this.
If necessary, screw the feet out fur-
ther.

Installing integrated “i” Dishwashers

Summary of Contents for G 665









































































Search results

Summary of Contents for G 665

Reviews:

Related manuals for G 665

Brands by name

Popular brands

Miele G 665, Operating Instructions Manual

Search results

Summary of Contents for G 665

Reviews:

Related manuals for G 665

Brands by name

Popular brands