Miele G 665 Operating Instructions Manual Download Page 33 | Manualshive

Page: 33 / 72

background image

Programme sequence indication

During the programme the programme
selector switch moves around the dial
to show which stage has been reached:

– Pre-wash (not shown)

– Wash cycle

– Interim rinse

– Final rinse

– Drying phase

The programme selector switch re-
mains stationary during the warm-up
phases of the wash and rinse cycle
until the required temperature has been
reached.

Note!
Do not finish a programme prematurely.
Important programme stages (e.g. re-
activating the water softener) could be
omitted.

A programme is complete only when
the programme selector switch is at the
"End" position.

The dishwasher can be opened and
crockery unloaded. If it is left closed,
the fan will continue for a few more
minutes to diminish any remaining mois-
ture.

This is recommended if the crockery is
not required immediately. This process
is extra to the wash programme.

The COLD PRE-WASH programme is
complete only when the programme se-
lector switch stops just before the start
point of the “UNIVERSAL PLUS” pro-
gramme.

Programme interruption

A programme is interrupted as soon as
the door is opened.
If the door is closed again the pro-
gramme will continue from the position
it was at when it was interrupted.

Warning
Water in the dishwasher may be
hot. Danger of scalding!
Only open the door if absolutely
necessary and exercise caution
when doing so.
Before closing the door leave it ajar
for approx. 20 secs. This will en-
able the temperature in the wash
cabinet to settle. Close the door
firmly making sure that it clicks into
place.

Switching on and off

33

«
...
31
32
33
34
35
...
»

Summary of Contents for G 665









































































Reviews:

No comments

Related manuals for G 665

Brand: Haier Pages: 11

Brand: Haier Pages: 11

Brand: Haier Pages: 11

Brand: Haier Pages: 17

Brand: Haier Pages: 14

Brand: Haier Pages: 2

Brand: Haier Pages: 10

Brand: Haier Pages: 35

Brand: Haier Pages: 18

Brand: Haier Pages: 28

Brand: Haier Pages: 8

Brand: Haier Pages: 40

Brand: Haier Pages: 54

Brand: Caloric Pages: 12

Brand: IFB Pages: 24

Brand: Gaggenau Pages: 76

Brand: Gaggenau Pages: 31

Brand: Kaiser Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands