Miele G 665 Operating Instructions Manual Download Page 16 | Manualshive

Page: 16 / 72

background image

Add rinse aid only until it is visible on
the surface of the filter in the open-
ing.

Close the flap firmly.
The flap must audibly engage, other-
wise water could get into the rinse
aid storage container during the pro-
gramme.

Mop up any split rinse aid. This pre-
vents over-forming occuring during
the next programme.

The flap should normally remain
closed. Only open it for adding more
rinse aid!

Wait until the ”Rinse aid” indicator on
the control panel lights up before ad-
ding more rinse aid.

Setting the dosage

The dosage adjuster (see arrow) in the
opening has settings from 1 to 6. It is
set to 3 at the factory, as the recom-
mended dose.This setting dispenses
approx. 3 ml rinse aid per programme.

If there are flecks on glasses after
drying use a higher setting.

If smearing appears on crockery use
a lower setting.

Adding rinse aid

16

«
...
14
15
16
17
18
...
»

Summary of Contents for G 665









































































Reviews:

No comments

Related manuals for G 665

Brand: Belling Pages: 18

Brand: Majestic Appliances Pages: 19

Millennia EDW24

Brand: Dacor Pages: 16

Brand: Samsung Pages: 36

Brand: Gorenje Pages: 16

FAVORIT 88015 VI

Brand: AEG Electrolux Pages: 36

Brand: Insinger Pages: 2

Brand: Haier Pages: 20

Brand: Haier Pages: 16

Brand: Haier Pages: 20

Brand: Haier Pages: 20

Brand: Haier Pages: 18

Brand: Haier Pages: 24

Brand: Haier Pages: 15

Brand: Haier Pages: 16

Brand: Haier Pages: 18

Brand: Haier Pages: 18

Brand: Haier Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands