Miele G 665 Operating Instructions Manual Download Page 56 | Manualshive

Page: 56 / 72

background image

4. Matching the facia panel to

the dimensions of the
adjacent drawer fronts

The facia panel can be aligned with the
drawer fronts of the kitchen units by ad-
justing the spacer bars.

Using an 8 mm socket spanner turn
clockwise or anti-clockwise until the
required height is reached.

If necessary some or all spacer bars
can be removed.

Adjustment range:

from 112 mm: facia panel without

spacer bars

to 145 mm:

facia panel with four
spacer bars,

to 154 mm:

using a fifth spacer bar

(special

accessory

at

extra cost).

Please note

After adjustment cut off any protruding
lengths of the screws.

Installing integrated “i” Dishwashers

56

«
...
54
55
56
57
58
...
»

Summary of Contents for G 665









































































Reviews:

No comments

Related manuals for G 665

Brand: Candy Pages: 30

Brand: IFB Pages: 33

Brand: lamber Pages: 19

Brand: Maidaid Halcyon Pages: 17

KITCHEN THINK BS 1400

Brand: Hotpoint Pages: 20

Brand: Maytag Pages: 9

Brand: Ariston Pages: 12

Brand: Brandt Pages: 42

Brand: Kuppersbusch Pages: 28

Brand: Gaggenau Pages: 14

Brand: Hotpoint Pages: 16

Brand: Frigidaire Pages: 13

Brand: Frigidaire Pages: 13

Brand: Frigidaire Pages: 16

Brand: Frigidaire Pages: 28

Brand: Frigidaire Pages: 12

Brand: Bosch Pages: 20

WAE24063GB Series

Brand: Bosch Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands