Miele G 665 Operating Instructions Manual Download Page 23

Page: 23 / 72

Adjusting the upper basket

(depending on model)

In order to gain more space for taller
pieces of crockery in the bottom or
upper basket, the upper basket can be
adjusted in three steps with 2 cm be-
tween each step.

Pull out the upper basket and loosen
the two locknuts on either side of the
basket.

Adjust the basket up or down to the
right height.

Tighten the locknuts.

The upper basket can also be set to an
angle if required.

Depending on the setting of the upper
basket the following dimensions can be
accommodated:

Dishwashers with cutlery tray

Upper

basket

position

plates Ø in cm

Upper

basket

Lower
basket

Top

15.5

Middle

17.5

Bottom

19.5

Dishwashers with cutlery basket

models with adjustable upper basket

Upper

basket

position

plates Ø in cm

Upper

basket

Lower

basket

Top

21.5

Middle

23.5

Bottom

25.5

models with non-adjustable basket

Plate Ø in upper basket: 23.5 cm
Plate Ø in lower basket: 28 cm

Loading the dishwasher

Summary of Contents for G 665









































































Search results

Summary of Contents for G 665

Reviews:

Related manuals for G 665

Brands by name

Popular brands

Miele G 665, Operating Instructions Manual

Search results

Summary of Contents for G 665

Reviews:

Related manuals for G 665

Brands by name

Popular brands