Miele G 6582 Operating Instructions Manual Download Page 13

Page: 13 / 108

Warning and Safety instructions



The manufacturer's warranty will be invalidated if the appliance is

not repaired by a Miele approved service technician.



Faulty components must only be replaced by genuine Miele spare

parts. The manufacturer can only guarantee the safety of the appli‐

ance when Miele replacement parts are used.



During installation, maintenance and repair work, the appliance

must be disconnected from the mains electricity supply.



If the connection cable is damaged, it must be replaced with a

special cable of the same type (available from Miele) by a Miele au‐

thorised service technician only.



In areas which may be subject to infestation by cockroaches or

other vermin, pay particular attention to keeping the appliance and

its surroundings in a clean condition at all times. Any damage which

may be caused by cockroaches or other vermin will not be covered

by the warranty.

Correct installation



The dishwasher must be installed and connected in compliance

with the installation instructions.



Be careful when installing the dishwasher. Wear protective

gloves to avoid injury on any sharp metal components.



The dishwasher must be correctly aligned to ensure problem-free

operation.



In order to ensure stability, built-under and integrated dishwash‐

ers must only be installed under a continuous worktop which is se‐

cured to adjacent cabinetry.

Summary of Contents for G 6582













































































































Search results

Summary of Contents for G 6582

Reviews:

Related manuals for G 6582

Brands by name

Popular brands

Miele G 6582, Operating Instructions Manual

Search results

Summary of Contents for G 6582

Reviews:

Related manuals for G 6582

Brands by name

Popular brands