Miele G 6582 Operating Instructions Manual Download Page 81

Page: 81 / 108

Problem solving guide

Unsatisfactory washing result

Problem

Possible cause and remedy

The dishes are not

clean.

The dishes were not loaded correctly.



See notes in "Loading the dishwasher".

The programme was not powerful enough.



Select a more intensive programme (see "Pro‐

gramme chart").

There is some stubborn soiling although most of the

crockery is only lightly soiled (e.g. with tea stains).



Use the

Sensor wash

programme option (see "Set‐

tings menu - Sensor wash").

Not enough detergent was dispensed.



Use more detergent, or change your detergent.

Items are blocking the path of the spray arms.



Rearrange the items so that the spray arms can

rotate freely.

The filter combination in the base of the wash cabinet

is not clean or is not correctly fitted. This may cause

the spray arm jets to get blocked.



Clean and/or fit the filter combination correctly.



Clean the spray arm jets if necessary (see "Clean‐

ing and care - Cleaning the spray arms").

The non-return valve is open and blocked. Dirty water

has flowed back into the wash cabinet.



Clean the drain pump and the non-return valve

(see "Maintenance").

Smearing appears on

glassware and cutlery,

there is a bluish sheen

on the surface of glass‐

ware; film can be wiped

off.

The rinse aid dosage is set too high.



Reduce the dosage (see "Settings menu - Rinse

aid").

Summary of Contents for G 6582













































































































Search results

Summary of Contents for G 6582

Reviews:

Related manuals for G 6582

Brands by name

Popular brands

Miele G 6582, Operating Instructions Manual

Search results

Summary of Contents for G 6582

Reviews:

Related manuals for G 6582

Brands by name

Popular brands