Miele G 6582 Operating Instructions Manual Download Page 89

Page: 89 / 108

Electrical connection

This dishwasher is supplied with a

mains cable and moulded plug ready

for connection to an AC single phase

supply, (230 - 240 V 50 Hz for NZ and

Australia) via a fused plug and suitable

switched socket.



The electrical socket must be

easily accessible after the dishwash‐

er has been installed. Do not con‐

nect the dishwasher to the mains

electricity supply by an extension

lead. Extension leads do not guaran‐

tee the required safety of the appli‐

ance (e.g. danger of overheating).

If the connection cable is damaged, it

must be replaced with a Miele cable of

the same type by a Miele approved

service technician only.
Do not connect the appliance to an in‐

verter such as those used with an au‐

tonomous energy source e.g.

solar

power

. When switched on, peak loads

in the system can cause the safety

switch-off mechanism to be triggered.

This can damage the electronic unit.

The machine must not be used with so-

called

energy-saving devices

either.

These reduce the amount of energy

supplied to the machine, causing it to

overheat.



Before connecting the appliance,

check that the connection data on

the data plate (voltage, frequency,

rated load and fuse rating) matches

the mains electricity supply. If in any

doubt, consult a qualified electrician.

The data plate is located on the right-

hand side of the door.



All electrical work must be car‐

ried out by a suitably qualified and

competent person in strict accord‐

ance with current local and national

safety regulations.

Summary of Contents for G 6582













































































































Search results

Summary of Contents for G 6582

Reviews:

Related manuals for G 6582

Brands by name

Popular brands

Miele G 6582, Operating Instructions Manual

Search results

Summary of Contents for G 6582

Reviews:

Related manuals for G 6582

Brands by name

Popular brands