Miele G 6582 Operating Instructions Manual Download Page 33

Page: 33 / 108

Loading the dishwasher

Adjusting the upper basket

In order to gain more space for taller

pieces of crockery in the bottom or up‐

per basket, the upper basket can be

adjusted on three levels with 2 cm be‐

tween each level.
The upper basket can also be set at an

angle with one side high and the other

side low. This can be useful to help pre‐

vent water being left in deep dishes etc.

Ensure, however, that the basket can

be inserted smoothly into the cabinet. It

is better to adjust the basket before

loading it.



Pull out the upper basket.

To raise the upper basket:



Pull the basket up until it clicks into

place.

To lower the upper basket:



Pull upwards on the levers at either

side of the upper basket.



Adjust the basket to the desired

height and then push the levers se‐

curely back down into position.

Depending on the setting of the upper

basket, the following plate dimensions

can be accommodated.

Dishwashers with cutlery basket

(see data plate for model number)

Upper

basket

level

Plate



in cm

Upper basket

Lower

basket

Stand‐

ard

XXL

Top

31 (35*)

Middle

Bottom

Dishwashers with cutlery tray

(see data plate for model number)

Upper

basket

level

Plate



in cm

Upper basket

Lower

basket

Stand‐

ard

XXL

Top

31 (35*)

Middle

Bottom

* When tilted, plates of up to 35 cm can be

accommodated (see "Lower basket").

Summary of Contents for G 6582













































































































Search results

Summary of Contents for G 6582

Reviews:

Related manuals for G 6582

Brands by name

Popular brands

Miele G 6582, Operating Instructions Manual

Search results

Summary of Contents for G 6582

Reviews:

Related manuals for G 6582

Brands by name

Popular brands