Miele G 4993 Page 58 Operating Instructions Manual Download

Page: 58 / 76

Frequently Asked Questions

Noises

Problem

Possible cause and solution

There is a knocking
noise in the wash cabi-
net.

A spray arm is hitting the dishes.



Interrupt the program, and rearrange the items
which are obstructing the spray arm.

There is a rattling noise
in the wash cabinet.

Dishes is moving around in the wash cabinet.



Interrupt the program and rearrange loose pieces.

A foreign object (e.g., a cherry pit) has become
lodged in the drain pump.



Remove the foreign object from the drain pump
(see "Maintenance - Cleaning the drain pump and
non-return valve").

There is a knocking
noise from the water
pipe

This may be caused by the installation or the diameter
of the water pipe.



This has no influence on dishwasher function. If in
doubt, contact a suitably qualified plumber.

Summary of Contents for G 4993













































































Search results

Summary of Contents for G 4993

Reviews:

Related manuals for G 4993

Brands by name

Popular brands

Miele G 4993, Operating Instructions Manual

Search results

Summary of Contents for G 4993

Reviews:

Related manuals for G 4993

Brands by name

Popular brands