Miele G 4993 Page 10 Operating Instructions Manual Download

Page: 10 / 76

IMPORTANT SAFETY INSTRUCTIONS

Proper installation



The dishwasher must be installed and connected in compliance

with the installation plan.



Be careful when installing the dishwasher. Wear protec-

tive gloves to avoid injury on any sharp metal components.



The dishwasher must be correctly aligned horizontally to ensure

problem-free operation.



In order to ensure stability, built-under and integrated dishwashers

must only be installed under a continuous counter which is secured
to adjacent cabinetry.



The door springs must be adjusted equally on both sides. They

are correctly adjusted when the door remains stationary when left
half open (approx. 45° opening angle). It is also important that the
door cannot fall open.
The appliance may only be used with correctly adjusted door
springs.

Summary of Contents for G 4993













































































Search results

Summary of Contents for G 4993

Reviews:

Related manuals for G 4993

Brands by name

Popular brands

Miele G 4993, Operating Instructions Manual

Search results

Summary of Contents for G 4993

Reviews:

Related manuals for G 4993

Brands by name

Popular brands