Miele G 1 Series Page 22 Operating Instructions Manual Download

Page: 22 / 76

Setting the rinse aid dosage

You can adjust the rinse aid dosage for
best results.

The rinse aid dosage can be set from
approx. 0-6 ml. It is set to a
recommended setting of approx. 3 ml
at the factory.

The dosage can turn out to be higher
than the set value due to the automatic
adjustment of the "Automatic
programme.

If spots appear on crockery and
glassware:

Increase the rinse aid dosage.

If clouding or smearing appears on
crockery and glassware:

Decrease the rinse aid dosage.

Switch the dishwasher off with the
On/Off button

Press the Start/Stop button in and

whilst holding it in

switch the

dishwasher on using the On/Off
button

Keep the Start/Stop button pressed in
for at least four seconds until the
"Start/Stop" indicator light comes on.

If this does not happen, start the
procedure from the beginning again.

Press the Delay start button three
times.

The "Delay start" indicator will flash
briefly three times at intervals.

p 3

will flash in the Time display.

This means that the rinse aid dosage
has been set to 3 ml at the factory.

The dosage set will show in the Time
display after the

Use the Start/Stop button to select
the rinse aid dosage you want.
The dosage amount alters each time
you press the button.

The programmed rinse aid dosage is
now stored in memory.

Switch the dishwasher off with the
On/Off button

Before using for the first time

Summary of Contents for G 1 Series













































































Search results

Summary of Contents for G 1 Series

Reviews:

Related manuals for G 1 Series

Brands by name

Popular brands

Miele G 1 Series, Operating Instructions Manual

Search results

Summary of Contents for G 1 Series

Reviews:

Related manuals for G 1 Series

Brands by name

Popular brands