Miele G 1 Series Page 42 Operating Instructions Manual Download

Page: 42 / 76

Adjust Sensor wash

You can adjust the Sensor wash
programme so that it will remove
stubborn soiling in a lightly soiled load.

Switch the dishwasher off with the
On/Off button

Press the Start/Stop button in and

whilst holding it in

switch the

dishwasher on using the On/Off
button

Keep the Start/Stop button pressed in
for at least four seconds until the
"Start/Stop" indicator light comes on.

If this does not happen, start the
procedure from the beginning again.

Press the Delay start button five
times.

The "Delay start" indicator will flash
briefly five times at intervals.

The message flashing in the Time
display shows whether the "Adjust
Sensor wash" function is activated or
deactivated.

– "

p 1

": The "Adjust Sensor wash"

function is activated.

– "

p 0

": The "Adjust Sensor wash"

function is deactivated.

To change the setting, press the
Start/Stop button.

Switch the dishwasher off with the
On/Off button

Additional functions

Summary of Contents for G 1 Series













































































Search results

Summary of Contents for G 1 Series

Reviews:

Related manuals for G 1 Series

Brands by name

Popular brands

Miele G 1 Series, Operating Instructions Manual

Search results

Summary of Contents for G 1 Series

Reviews:

Related manuals for G 1 Series

Brands by name

Popular brands