Miele Dimension G 5670 SCVi Operating Instructions Manual Download Page 17 | Manualshive

Page: 17 / 72

background image

Rinse aid indicator

When the

(

Refill rinse aid

message

appears, the reservoir contains
sufficient rinse aid for 2 - 3 programs
only.

^

Add rinse aid once the program has
finished.

^

Confirm with the center button.

The "Refill rinse aid" message will go
out.

If using "Tab" detergent products in
your dishwasher, the messages can
be turned off if desired (see
"Settings - Deactivate indicators").

If you switch to using detergent that
does not contain salt or rinse aid, it
is important to remember to
replenish the salt and rinse aid and
to turn the indicators back on.

Before using for the first time

17

«
...
15
16
17
18
19
...
»

Summary of Contents for Dimension G 5670 SCVi









































































Reviews:

No comments

Related manuals for Dimension G 5670 SCVi

Brand: GE Pages: 78

Brand: Smeg Pages: 10

Brand: N'DUSTRIO Pages: 27

Brand: Amana Pages: 44

Brand: Parmco Pages: 24

Brand: Hoover Pages: 20

Brand: Monogram Pages: 86

Brand: Küppersbusch Pages: 28

Brand: Icecool Pages: 112

Brand: John Lewis Pages: 32

Brand: NEFF Pages: 30

Brand: AEG Electrolux Pages: 36

Brand: Hanseatic Pages: 72

Brand: Hoover Pages: 88

Brand: ZANKER Pages: 22

Brand: Samsung Pages: 208

Brand: Samsung Pages: 132

Brand: Samsung Pages: 132

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands