Miele Dimension G 5670 SCVi Operating Instructions Manual Download Page 47

Page: 47 / 72

Repairs should only be carried out by a qualified and trained person in

accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.

Technical faults

Problem

Possible fault

Solution

After the dishwasher was
turned on with the

button, the display stays
off and the "Start/Stop"
indicator does not flash.

The machine is not
plugged in.

Insert the plug.

The circuit breaker has
tripped.

Reset the circuit breaker.
See the data plate for
minimum amperage.

The dishwasher stops
during a program.

The circuit breaker has
tripped.

– Reset the circuit breaker

(see the data plate for
minimum amperage).

– If the circuit breaker

trips again. Contact
Miele.

One of the following
faults appears on the
display:

Before fixing the fault:

– Press the

button to

turn the dishwasher off.

;

Fault FXX

There may be a
technical fault.

After a few seconds:

– Turn the dishwasher on.

– Select the desired

program.

– Press the Start/Stop

button.

If the fault is indicated
again, a technical fault has
occurred.

– Contact Miele.

Waterproof

The waterproof system
has activated.

– Turn off the water

supply.

– Contact Miele.

Frequently Asked Questions

Summary of Contents for Dimension G 5670 SCVi









































































Search results

Summary of Contents for Dimension G 5670 SCVi

Reviews:

Related manuals for Dimension G 5670 SCVi

Brands by name

Popular brands

Miele Dimension G 5670 SCVi, Operating Instructions Manual

Search results

Summary of Contents for Dimension G 5670 SCVi

Reviews:

Related manuals for Dimension G 5670 SCVi

Brands by name

Popular brands