Miele Dimension G 5670 SCVi Operating Instructions Manual Download Page 48

Page: 48 / 72

Faults in the water intake/water drain

Problem

Possible fault

Solution

One of the following
faults appears on the
display:

Before fixing the fault:

– Press the

button to turn

the dishwasher off.

Open water supply

The water supply valve
is closed.

Open the water supply valve all
the way.

Water intake

Before fixing the fault:

– Press the

button to turn

the dishwasher off.

Fault in the water
intake.

– Open the water supply all

the way and restart the
program.

– Clean the water intake filter

(see "Cleaning and Care").

– The water pressure at the

water connection is less than
4.35 psi. Consult a plumber.

Drain

Fault in the water drain.
There might be water in
the wash cabinet.

– Clean the triple filter (see

"Cleaning and care").

– Clean the drain pump (see

"Cleaning and Care").

– Clean the non-return valve

(see "Cleaning and Care").

– Remove any kinks in the

drain hose.

Frequently Asked Questions

Summary of Contents for Dimension G 5670 SCVi









































































Search results

Summary of Contents for Dimension G 5670 SCVi

Reviews:

Related manuals for Dimension G 5670 SCVi

Brands by name

Popular brands

Miele Dimension G 5670 SCVi, Operating Instructions Manual

Search results

Summary of Contents for Dimension G 5670 SCVi

Reviews:

Related manuals for Dimension G 5670 SCVi

Brands by name

Popular brands