Midea Mono 3D Service Manual Download Page 27

Page: 27 / 106

8. Electronic Function

8.1 Abbreviation

T1: Indoor room temperature

T2: Coil temperature of evaporator

T3: Coil temperature of condenser

T4: Outdoor ambient temperature

T5: Compressor discharge temperature

8.2 Display function

8.2.1 Icon explanation on indoor display board.

ION indication lamp(optional function)

：

This lamp illuminates when Clean Air

feature is activated.

DEFROST indication lamp(For cooling & heating models only):

Lights up

when the air conditioner starts defrosting automatically or when the warm air

control feature is activated in heating operation.

OPERATION indication lamp

：

This lamp illuminates when the air conditioner is in

operation.

TIMER indication lamp

：

Lights up during Timer operation.

Temperature indicator

：

Displays the temperature settings when the air conditioner

is operational. Displays the malfunction code.

Summary of Contents for Mono 3D











































































































Search results

Summary of Contents for Mono 3D

Reviews:

Related manuals for Mono 3D

Brands by name

Popular brands

Midea Mono 3D, Service Manual

Search results

Summary of Contents for Mono 3D

Reviews:

Related manuals for Mono 3D

Brands by name

Popular brands