manualshive.com logo in svg

Microdigital MDR-i0016(25/36), User Manual, Page: 41 / 64

Share
Download
Microdigital MDR-i0016(25/36) User Manual Download Page 41

 

41

 

3.8.4 Upgrading Firmware   

 

 

 

Microdigital MDR-i0016(25/36)stops recording during the upgrade 
process and it resumes recording when the unit restarts after 
completion of upgrade process.   

 

 

If upgrade process is not completed due to power failure or 

unintended interruption by user, Microdigital MDR-i0016(25/36)restores 
the current system automatically when it is rebooted.   

 

 

When firmware is upgraded, the existing settings are applied on the 
new system automatically as is set on the current system.   

 

 

User may upgrade the NVR firmware through USB interfaced memory.   

 

1.  Put a new firmware of Microdigital MDR-i0016(25/36)on a USB thumb drive and attach the drive to 

Microdigital MDR-i0016(25/36).   

 

2.  Open ‘Setup’ menu of Microdigital MDR-i0016(25/36)and go to ‘System’ tab. 

 

3.  Click ‘…’ (

/browse) button.   

 

 

4.  Select ‘MDR-i0016(25/36)Upgrade.exe’ file in the folder and click ‘Open’ button. 

 

 

5.  Click ‘Upgrade’ (

) button.   

Summary of Contents for MDR-i0016(25/36)

































































Reviews:

No comments